DATA LIST / ACTIVE TEST
DATA LIST
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
(a) Warm up the engine.
(b) Turn the engine switch off.
(c) Connect the Techstream to the DLC3.
(d) Turn the engine switch on (IG).
(e) Turn the Techstream on.
(f) Enter the following menus: Chassis / ABS/VSC/TRAC/EPB / Data List.
(g) According to the display on the Techstream, read the Data List.
Chassis > ABS/VSC/TRAC/EPB > Data List|
Tester Display | Measurement Item |
Range | Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
ABS Warning Light | ABS warning light |
ON or OFF | ON: Warning light on OFF: Warning light off |
- |
| Brake Warning Light |
Brake system warning light (red indicator) |
ON or OFF | ON: Warning light on OFF: Warning light off |
- |
| Stop Light SW |
Stop light switch assembly |
ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released |
- |
| Parking Brake SW |
Parking brake switch assembly |
ON or OFF | ON: Parking brake applied OFF: Parking brake released |
- |
| Main Idle SW |
Main idle switch | ON or OFF |
ON: Accelerator pedal released OFF: Accelerator pedal depressed |
- |
| Gear Position |
Gear position information |
"P,N", R, 1st-10th, Fail or Not R |
Actual gear position |
- |
| Shift Lever Position |
Shift lever position information |
"P,N", R, D/M, 1st-6th/B or Fail |
Actual shift lever position |
- |
| Shift Information |
Shift information | ON or OFF |
ON: During gear change OFF: Not during gear change |
- |
| Inspection Mode |
Inspection mode | Other or Inspect |
Other: Normal mode Inspect: Inspection mode |
- |
| Number of IG ON(Inspection) |
Number of times engine switch turned on (IG) after entering inspection mode |
Min.: 0, Max.: 255 | - |
- |
| Master Cylinder Sensor |
Master cylinder pressure sensor reading |
Min.: 0.00 V, Max.: 5.00 V |
Brake pedal released: 0.20 to 0.40 V |
Reading increases when brake pedal is depressed |
|
Deceleration Sensor | Acceleration sensor reading |
Min.: -18.525 m/s2, Max.: 18.387 m/s2 |
- | During deceleration/acceleration: Changes continuously |
|
Zero Point of Decele | Memorized zero value |
Min.: -25.10 m/s2, Max.: 24.90 m/s2 |
- | - |
|
Deceleration Sensor2 | Acceleration sensor 2 reading |
Min.: -18.525 m/s2, Max.: 18.387 m/s2 |
- | During deceleration/acceleration: Changes continuously |
|
Zero Point of Decele2 | Memorized zero value |
Min.: -25.10 m/s2, Max.: 24.90 m/s2 |
- | - |
|
Yaw Rate Sensor | Yaw rate sensor |
Min.: -128°/s, Max.: 127°/s |
Vehicle stopped: 0°/s Turning right: -128 to 0°/s Turning left: 0 to 127°/s |
- |
| Zero Point of Yaw Rate |
Memorized zero value | Min.: -128°, Max.: 127° |
- | After completing zero point calibration: 0° |
|
Steering Angle Sensor | Steering angle sensor |
Min.: -3276.8°, Max.: 3276.7° |
Turning left: Increases Turning right: Decreases |
- |
| Zero Point of Steering Angle |
Memorized zero value | Min.: -3276.8°, Max.: 3276.7° |
- | After steering angle sensor zero point calibration: 0° |
|
Lateral G | Lateral G |
Min.: -25.10 m/s2, Max.: 24.90 m/s2 |
- | During turning: Changes in proportion with lateral acceleration |
|
Forward and Rearward G |
Forward and rearward G |
Min.: -25.10 m/s2, Max.: 24.90 m/s2 |
- | During acceleration/deceleration: Changes in proportion with acceleration |
|
Yaw Rate Value | Yaw rate value |
Min.: -128°/s, Max.: 127°/s |
- | During turning: Changes in proportion with yaw |
|
Steering Angle Value | Steering angle value |
Min.: -3276.8°, Max.: 3276.7° |
- | During steering operation: Changes in proportion with steering wheel rotation |
|
Stop Light Relay | Stop light control relay (Stop light switch assembly) (STP2 terminal input) | ON or OFF |
ON: Brake pedal depressed OFF: Brake pedal released |
- |
| Slip Indicator Light |
Slip indicator light | ON or OFF |
ON: Indicator light on OFF: Indicator light off |
- |
| FR Wheel Speed |
Front wheel speed sensor RH reading |
Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) |
Vehicle stopped: 0 km/h (0 mph) |
When driving at constant speed: No large fluctuations |
|
FL Wheel Speed | Front wheel speed sensor LH reading |
Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) |
Vehicle stopped: 0 km/h (0 mph) |
When driving at constant speed: No large fluctuations |
|
RR Wheel Speed | Rear wheel speed sensor RH reading |
Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) |
Vehicle stopped: 0 km/h (0 mph) |
When driving at constant speed: No large fluctuations |
|
RL Wheel Speed | Rear wheel speed sensor LH reading |
Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) |
Vehicle stopped: 0 km/h (0 mph) |
When driving at constant speed: No large fluctuations |
|
Vehicle Speed | Maximum wheel speed sensor reading |
Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) |
Vehicle stopped: 0 km/h (0 mph) |
When driving at constant speed: No large fluctuations |
|
FR Wheel Acceleration | Front wheel RH acceleration |
Min.: -200.84 m/s2, Max.: 199.27 m/s2 |
- | During deceleration/acceleration: Changes continuously |
|
FL Wheel Acceleration | Front wheel LH acceleration |
Min.: -200.84 m/s2, Max.: 199.27 m/s2 |
- | During deceleration/acceleration: Changes continuously |
|
RR Wheel Acceleration | Rear wheel RH acceleration |
Min.: -200.84 m/s2, Max.: 199.27 m/s2 |
- | During deceleration/acceleration: Changes continuously |
|
RL Wheel Acceleration | Rear wheel LH acceleration |
Min.: -200.84 m/s2, Max.: 199.27 m/s2 |
- | During deceleration/acceleration: Changes continuously |
|
Stop Light Relay Output |
Stop light control relay (Stop light switch assembly) (STPO terminal output) |
ON or OFF | ON: Relay output on OFF: Relay output off |
- |
| EBS Relay |
Stop light control relay (Stop light switch assembly) (for emergency brake signal) |
ON or OFF | OFF: Relay off |
Not applicable to this vehicle |
|
FR Wheel ABS Ctrl Status |
Front wheel RH ABS control status |
ON or OFF | ON: During control |
- |
| FL Wheel ABS Ctrl Status |
Front wheel LH ABS control status |
ON or OFF | ON: During control |
- |
| RR Wheel ABS Ctrl Status |
Rear wheel RH ABS control status |
ON or OFF | ON: During control |
- |
| RL Wheel ABS Ctrl Status |
Rear wheel LH ABS control status |
ON or OFF | ON: During control |
- |
| FR Wheel EBD Ctrl Status |
Front wheel RH EBD control status |
ON or OFF | ON: During control |
- |
| FL Wheel EBD Ctrl Status |
Front wheel LH EBD control status |
ON or OFF | ON: During control |
- |
| RR Wheel EBD Ctrl Status |
Rear wheel RH EBD control status |
ON or OFF | ON: During control |
- |
| RL Wheel EBD Ctrl Status |
Rear wheel LH EBD control status |
ON or OFF | ON: During control |
- |
| BA Ctrl Status |
BA control status | ON or OFF |
ON: During control | - |
|
PBA Ctrl Status | PBA control status |
ON or OFF | ON: During control |
- |
| TRC(TRAC) Ctrl Status |
TRAC control status | ON or OFF |
ON: During control | - |
|
TRC(TRAC) Engine Ctrl Status |
TRAC engine control status |
ON or OFF | ON: During control |
- |
| TRC(TRAC) Brake Ctrl Status |
TRAC brake control status |
ON or OFF | ON: During control |
- |
| FR Wheel VSC Ctrl Status |
Front wheel RH VSC control status |
ON or OFF | ON: During control |
- |
| FL Wheel VSC Ctrl Status |
Front wheel LH VSC control status |
ON or OFF | ON: During control |
- |
| RR Wheel VSC Ctrl Status |
Rear wheel RH VSC control status |
ON or OFF | ON: During control |
- |
| RL Wheel VSC Ctrl Status |
Rear wheel LH VSC control status |
ON or OFF | ON: During control |
- |
| Engine Revolutions |
Engine speed | Min.: 0 rpm, Max.: 65535 rpm |
Engine stopped: 0 rpm | When engine speed is constant: No large fluctuations |
|
Real Engine Torque | Real engine torque |
Min.: -1024 Nm, Max.: 1023 Nm |
- | - |
|
Accelerator Opening Angle % |
Percentage of accelerator pedal opening angle |
Min.: 0.0%, Max.: 127.5% |
Accelerator pedal released: 0.0% |
During accelerator pedal operation: Changes in proportion with the pedal movement |
|
Solenoid Relay | ABS solenoid relay |
ON or OFF | ON: ABS solenoid relay on OFF: ABS solenoid relay off |
- |
| TR(A)C/VSC Solenoid (SRM2) |
Master cut solenoid (SRM2) |
ON or OFF | ON: During control |
- |
| TR(A)C/VSC Solenoid (SRM1) |
Master cut solenoid (SRM1) |
ON or OFF | ON: During control |
- |
| TR(A)C/VSC Solenoid (SRC2) |
Master cut solenoid (SRC2) |
ON or OFF | ON: During control |
- |
| TR(A)C/VSC Solenoid (SRC1) |
Master cut solenoid (SRC1) |
ON or OFF | ON: During control |
- |
| ABS Solenoid (SFRH) |
ABS solenoid (SFRH) | ON or OFF |
ON: During control | - |
|
ABS Solenoid (SFRR) | ABS solenoid (SFRR) |
ON or OFF | ON: During control |
- |
| ABS Solenoid (SFLH) |
ABS solenoid (SFLH) | ON or OFF |
ON: During control | - |
|
ABS Solenoid (SFLR) | ABS solenoid (SFLR) |
ON or OFF | ON: During control |
- |
| ABS Solenoid (SRRH) |
ABS solenoid (SRRH) | ON or OFF |
ON: During control | - |
|
ABS Solenoid (SRRR) | ABS solenoid (SRRR) |
ON or OFF | ON: During control |
- |
| ABS Solenoid (SRLH) |
ABS solenoid (SRLH) | ON or OFF |
ON: During control | - |
|
ABS Solenoid (SRLR) | ABS solenoid (SRLR) |
ON or OFF | ON: During control |
- |
| EFI Communication Open |
ECM communication open detection |
Error or Normal | Error: Momentary interruption Normal: Normal | - |
|
Yaw Rate Open | Yaw rate sensor open detection |
Error or Normal | Error: Momentary interruption Normal: Normal | - |
|
Deceleration Open | Acceleration sensor open detection |
Error or Normal | Error: Momentary interruption Normal: Normal | - |
|
Steering Open | Steering angle sensor open detection |
Error or Normal | Error: Momentary interruption Normal: Normal | - |
|
IG1 Voltage Value | IG1 voltage value |
Min.: 0.00 V, Max.: 20.00 V |
- | Changes in proportion to battery voltage |
|
BS1 Voltage Value | +BS voltage value |
Min.: 0.00 V, Max.: 20.00 V |
- | Changes in proportion to battery voltage |
|
MT Voltage Value | Motor voltage value |
Min.: 0.00 V, Max.: 20.00 V |
- | Changes in proportion to battery voltage |
|
BH Standby Light | Brake hold standby indicator light |
ON or OFF | ON: Indicator light on OFF: Indicator light off |
- |
| BH Operated Light |
Brake hold operated indicator light |
ON or OFF | ON: Indicator light on OFF: Indicator light off |
- |
| TRAC/VSC Off Mode |
TRAC/VSC off mode | Normal, TRC OFF,VSC Expert Mode or VSC OFF |
Normal: Normal mode TRC OFF: TRAC off mode VSC Expert Mode: VSC expert mode VSC OFF: VSC off mode |
- |
| Number of DTC |
Number of DTC recorded |
Min.: 0, Max.: 255 | - |
- |
| IG Voltage Value Decreased |
+BS voltage value decrease detection |
Error or Normal | Error: Voltage low Normal: Normal | - |
|
IG Voltage Value Increased |
+BS voltage value increase detection |
Error or Normal | Error: Voltage high Normal: Normal | - |
|
Brake Hold Ready | Brake hold control permission status |
OFF or ON | ON: Brake hold control permitted OFF: Brake hold control not permitted |
- |
| Brake Hold Control Mode |
Brake hold control mode |
OFF, ON, Release or EPB |
OFF: Brake hold control is not operating ON: Brake hold control is operating Release: Brake hold control is released EPB: Parking brake is engaged during brake hold control |
HINT: EPB stands for electric parking brake. |
ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed.
Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
(a) Warm up the engine.
(b) Turn the engine switch off.
(c) Connect the Techstream to the DLC3.
(d) Turn the engine switch on (IG).
(e) Turn the Techstream on.
(f) Enter the following menus: Chassis / ABS/VSC/TRAC/EPB / Active Test.
(g) According to the display on the Techstream, perform the Active Test.
Chassis > ABS/VSC/TRAC/EPB > Active Test|
Tester Display | Measurement Item |
Control Range | Diagnostic Note |
|---|---|---|---|
|
ABS Warning Light | ABS warning light |
Warning light OFF/ON | Observe combination meter assembly |
|
Brake Warning Light | Brake system warning light (red indicator) |
Warning light OFF/ON | Observe combination meter assembly |
|
Motor Relay | ABS motor relay |
Relay OFF/ON | Operating sound of motor can be heard |
|
Stop Light Relay | Stop light control relay (Stop light switch assembly) |
Relay OFF/ON | Stop lights come on |
|
ABS Solenoid (SRLR) | ABS solenoid (SRLR) |
Solenoid ON/OFF | Operation sound of solenoid (clicking sound) can be heard |
|
ABS Solenoid (SRLH) | ABS solenoid (SRLH) |
Solenoid ON/OFF | Operation sound of solenoid (clicking sound) can be heard |
|
ABS Solenoid (SRRR) | ABS solenoid (SRRR) |
Solenoid ON/OFF | Operation sound of solenoid (clicking sound) can be heard |
|
ABS Solenoid (SRRH) | ABS solenoid (SRRH) |
Solenoid ON/OFF | Operation sound of solenoid (clicking sound) can be heard |
|
ABS Solenoid (SFLR) | ABS solenoid (SFLR) |
Solenoid ON/OFF | Operation sound of solenoid (clicking sound) can be heard |
|
ABS Solenoid (SFLH) | ABS solenoid (SFLH) |
Solenoid ON/OFF | Operation sound of solenoid (clicking sound) can be heard |
|
ABS Solenoid (SFRR) | ABS solenoid (SFRR) |
Solenoid ON/OFF | Operation sound of solenoid (clicking sound) can be heard |
|
ABS Solenoid (SFRH) | ABS solenoid (SFRH) |
Solenoid ON/OFF | Operation sound of solenoid (clicking sound) can be heard |
|
VSC/TRAC Solenoid (SRMR) |
Master cut solenoid (SRM2) |
Solenoid ON/OFF | Operation sound of solenoid (clicking sound) can be heard |
|
VSC/TRAC Solenoid (SRMF) |
Master cut solenoid (SRM1) |
Solenoid ON/OFF | Operation sound of solenoid (clicking sound) can be heard |
|
VSC/TRAC Solenoid (SRCR) |
Master cut solenoid (SRC2) |
Solenoid ON/OFF | Operation sound of solenoid (clicking sound) can be heard |
|
VSC/TRAC Solenoid (SRCF) |
Master cut solenoid (SRC1) |
Solenoid ON/OFF | Operation sound of solenoid (clicking sound) can be heard |
|
BH Standby Light | Brake hold standby indicator light |
Indicator light OFF/ON |
|
| BH Operated Light |
Brake hold operated indicator light |
Indicator light OFF/ON |
|
| TRC(TRAC) OFF Indicator Light |
Multi-information display (Traction Control Turned Off) |
Display OFF/ON | Observe combination meter assembly |
|
VSC OFF Indicator Light |
VSC OFF indicator light |
Indicator light OFF/ON |
Observe combination meter assembly |
|
Slip Indicator Light | Slip Indicator light |
Indicator light OFF/ON |
Observe combination meter assembly |
|
EBS Relay | Stop light switch assembly output (Emergency brake signal operation) |
OFF/ON | Not applicable to this vehicle |
|
ABS Solenoid | ABS solenoid (SRLR, SRLH, SRRR, SRRH, SFLR, SFLH, SFRR, SFRH) |
Solenoid SRLR/SRLH/SRRR/ SRRH/SFLR/SFLH/SFRR/SFRH |
Operation sound of solenoid (clicking sound) can be heard |
|
VSC/TRC(TRAC) Solenoid |
Master cut solenoid (SRM1, SRM2, SRC1, SRC2) |
Solenoid SRMF/SRMR/SRCF/ SRCR/SMF/SMR/SPFR/SPFL |
Operation sound of solenoid (clicking sound) can be heard |
Toyota Avalon (XX50) 2019-2022 Service & Repair Manual > Smart Key System(for Start Function, Hv Model): Engine Immobiliser System Circuit Short to Battery (B279A12). Engine Immobiliser System Incorrect Assembly (B279C95). Ignition Hold Monitor Malfunction (B2271)
Engine Immobiliser System Circuit Short to Battery (B279A12) DESCRIPTION If the communication line (IMI - EFIO) between the hybrid vehicle control ECU and certification ECU (smart key ECU assembly) is stuck high, the hybrid vehicle control ECU will store this DTC. DTC No. Detection Item DTC Detectio ...
